Recent Posts

Archives

Category

Odroid-hc4

Odroid-hc4-01-rno
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4
Odroid-hc4

Odroid-hc4
HC4-Plus versionincludes OLED Displayand RTC Clock Battery HC4-Base versiondoes not include OLEDDisplay and RTC ClockBattery, but will be available later as anoptional add-on See the Not Included section below for additional items needed and/or recommended for operation The ODROID-HC4 is a mini PC with a dual SATA drive dock which makes an affordable solution for a Do-It-Yourself Network Attached Storage (NAS) server. This server centralizes data and enables users to share and stream multimedia files to phones, tablets and other devices on a network. Ideal for workgroups, families, and single users. A wide variety of software is available to tailor the ODROID-HC4 to your specific needs. Upgrade the storage capacity of this server with one or two larger HDD/SSD. The HC4 is built with two high performance SATA port and a Gigabit Ethernet port, to build a faster network storage device, and also supports RAID configurations. The HC4 is designed to hold 2x 2.5 inch HDD/SSDs or 3.5inch HDDs in any combination. The HC4 is based on the very powerful Amlogic S905X3 chip, just like the ODROID-C4. It can run Samba, FTP, NFS, SSH, NGINX, Apache, SQL, Docker, WordPress and other server software smoothly with full Linux distributions like Ubuntu, Debian, Arch and OMV. Links to compliance documentation available at the bottom of this listing. Version includes OLED Display and RTC Clock Battery. Version does not include OLED Display and RTC Clock Battery, but will be available later as an optional add-on. Section below for additional items needed and/or recommended for operation. The ODROID-HC4 is a mini PC with a dual SATA drive dock which makes an affordable solution for a Do-It-Yourself Network Attached Storage (NAS) server. The HC4 is based on the very powerful Amlogic S905X3 chip, just like the. It can run Samba, FTP, NFS, SSH, NGINX, Apache, SQL, Docker, WordPress and other server software smoothly with. Full Linux distributions like Ubuntu, Debian, Arch and OMV. Additional items required to operate – see “NOT INCLUDED” section below. Amlogic S905X3 Processor Quad-Core Cortex-A55 (1.8GHz). 4GB DDR4 RAM with 32-bit bus width (PC4-21333 grade). Dual SATA-3 port for 3.5inch and/or 2.5inch HDD/SSD storage. UHS-1 capable micro-SD card slot for boot media. Gigabit Ethernet port (RTL8211F). Digital audio over HDMI. USB 2.0 Host. 1x DC Jack (5.5/2.1mm) rated for 14.515.5VDC. 84 x 90.5 x 25mm. 280g including heatsink, fan and case. Form Factor: Board Dimensions: 84mm x 90.5mm x 25.0mm Heatsink Dimensions: 40mm x 32mm x 10mm Weight: 280g including heatsink, fan and case. Processor: Amlogic S905X3 Processor L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processors Quad-Core Cortex-A55 (1.800GHz) ARMv8-A architecture with Neon and Crypto extensions Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz). Memory: DDR4 4GiB with 32-bit bus width Data rate: 2640 MT/s (PC4-21333 grade) 1.2Volt low power design. Storage: 1x Micro SD slot (DS/HS mode up to UHS-I SDR104). Networking : 1x GbE LAN ports (RJ45, supports 10/100/1000 Mbps). Realtek RTL8211F (Ethernet transceiver). Green LED: Flashing by data traffics at 100Mbps connection. Amber LED: Flashing by data traffics at 1000Mbps connection. Audio: 1x HDMI digital output. Cooler: 1x Passive heatsink (40x32x10 mm) on the CPU of PCB board. 1x Hydraulic Bearing FAN. Max Speed RPM : 4,000. Air Flow CFM : 4.3. Air Pressure (In H2O) : 0.053. Noise Level(dBA) : 23.9. Dimension : 40 x 40 x 10.6 mm. Wire & Connector : 80mm, 4 pin 1.25mm pitch. External I/O: 1x USB 2.0 host port 1x Debug serial console (UART) 2x SATA Connectors. Other features: IR receiver for remote controller System LED Indicators. Red (POWER) – Solid light when DC power is connected. Blue (ALIVE) – Flashing like heartbeat while Kernel is running. Power: 1x DC jack: outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm DC input: 14.5V 15.5V. DC 15V/4A power adapter is recommended. Power consumption with two ST2000DM006 HDDs. IDLE(with HDD in spin-down) : 5.88W. Active(using SAMBA): 15.59W. No power supply included. OLED display with integrated RTC battery is optional (included on the Plus model). Recommended if connecting more than one USB device to the HC4. No WiFi included – Wired networks are preferable for NAS units due to bandwidth and reliability, but we have. Highly recommended for tinkering with u-boot, kernels, multiple installs and more. Sorry, our items are NOT available for pick-up. No additional information at this time. You might also like. The item “ODROID-HC4″ is in sale since Thursday, December 31, 2020. This item is in the category “Crafts\Needlecrafts & Yarn\Embroidery & Cross Stitch\Hand Embroidery Kits\Cross Stitch Kits”. The seller is “respectech” and is located in Ukiah, California. This item can be shipped worldwide.
  • Brand: Hardkernel

Odroid-hc4